聚丙烯網狀撕裂纖維填充繩
Reticular polypropylene filler ropes
● 用途及特性 Uses characteristics
本產品使用拉絲級聚丙烯樹脂主要原料。采用擠出成型法制得填充用聚丙烯網狀撕裂纖維,該產品具有不吸濕無毒柔軟富有彈性,拉力強和不霉爛不腐蝕耐濕等物化性能,并肯有高頻絕緣性能好,擊穿電壓高等性能。能適用于各種電力電費交聯電纜填充之用。
The main raw material of this product is drawing class polypropylene resin. Lacerated reticular polypropylene filler fibers is produced by extrusion method. This product is non-absorbent, soft, flexible, with high tensile strength, mouldproof, corrosionproof, and heatresisting. This product can be applied to all kinds of power cable as filler in cross-linking process.
● 產品特性 Uses characteristics
外觀:顏色:白色且色澤均勻一致無污染。
網格:輕拉展開成網,網格均勻。
柔軟程度:塑化良好,手感柔軟似棉紗。
繞卷:整齊不松散。
Appearance: white, clean, and in even color
spread out into a net with uniform grids when gently pulled
well plasticized and soft like cotton yarns
rolled tidily without loose
● 技術參數 Technical parameters
項目 Item | 指標 Index | 試驗方法 Test method | |||||
外觀 | 丙纖應干燥無污染,無雜質,輕拉成網,網格均勻 Propylene fiber should be dry, clean, impurity-free, gently pulled to nets with uniform grids | 目測 Visual | |||||
斷裂強力 Breaking strength | 規格mm Type | 30 | 40 | 60 | 90 | 120 | D |
N≥ | 52 | 60 | 68 | 120 | 135 | ||
直徑 mm Diameter | 2 | 2.5 | 3 | 4 | 4.5 | 千分尺 micrometer | |
定量 g/m Weight | 1.40-1.62 | 2.0-2.17 | 3.0-3.25 | 4.0-4.50 | 5.00-6.50 | 稱重法 weighing method | |
捻度 Twistbreak | 丙纖應以(3-5)捻/200mm 的捻度加捻 on speed of (3-5) twisting /200 mm | 用解捻式捻度計進行, 夾鉗間距為200mm Propylene fiber shall be twisted with a twistbreak twist machine clip spacing 200mm |
在溫度為20℃±2℃、濕度為65%±5%條件下,用Y501型織物強力機或其他合適的試驗機進行。每卷取樣一個,每批5個。試驗時,上、下夾鉗距離為220mm,下夾鉗的下降速度為110mm/min。把試樣加100g張力使其伸直夾入土上、下夾鉗中,開動強力機,記錄讀數,精確到0.1kg。以5個試樣的斷強力算術平均值(計算至小數點后一位)作為該批丙纖的斷裂強力值。
The experiment is carried out at a temperature of 20℃±2℃, and a humidity of 65%±5%, with the Y501 fabric strength test machine or other suitable machine. One sample is selected from each batch. The distance between the upper and lower clamps is 220mm, the falling rate of the lower clamp is the 110mm/min. Add to the sample clip is straightly clamped between the upper and lower clamps, and a tension of 100g is added to it. Then start the test machine, and record the readings with the accuracy of 0.1kg. Count the arithmetic mean value of 5 samples off to ( rounded to one decimal place ) as the breaking strength value of the batch of PP fiber.
注:特殊規格及可在供需合同中規定。
NOTE: Supplier with special requirements of types can be customer.
● 貯存 Storage
本產品自出公司之日起貯存期為6個月, 貯存環境應保持通風、干燥、陰涼。
This product is valid for 6 months since the date of manufacture, and should be stored in a dry and clean warehouse.